Economic Design of Rectifying Single Sampling Plan (RSS) when Inspection Error is considered
DOI:
:
https://doi.org/10.5281/zenodo.6513578
Keywords:
Acceptable Quality Level,, Lot Tolerant Percent defective Average Total Inspection,, producer’s risk,, Consumer’s risk.Abstract
In this paper, Hsu and Hsu (2012) Single-sampling cost minimization model is modified to incorporate inspection error. The modified model aims to maximize the probability of lot acceptance with an acceptable quality level (AQL) and minimizes the probability of lot acceptance with lot tolerant percent defective (LTPD). An optimal sampling plan that minimize the total cost and satisfied both the producer’s and the consumer’s risk requirement is determined. A comparison between the existing model and the modified model using the Operating characteristic (OC) curve, Average Total Inspection (ATI), and Total Cost (TC) is made. Sensitivity analysis is also carried out. Results showed that the modified model performed better and is more economical than the existing model in terms of cost-effectiveness.
References
Amitava, M. (2016). Fundamentals of Quality Control and Improvement. 4th Edition, John willey & Sons,Inc,New Jersey, Canada, Pp.502-510
Anuja, S., Ratika, S., Tulka, S., and Singh, V. (2013). A Novel Method for Dynamic Sampling Plan and Inspection Policies for Quality Assurance. Asian Research Journal of Business Management, 2(1):34-43
Banovac, E., Darko, P., and Nikola, V. (2012). Mathematical Aspect of Acceptance Sampling Procedure. International Journal of Mathematical Models and Methods in Applied Sciences, 5(6):1-9
Castillo –villar, K. K.., Smith, N. R.., and Simonton, J. L. (2012). The Impact of the Cost of Quality on Serial-chain Network Design. International Journal of Production Research, 50(19): 5544-5566.
Chen, C., Espanchin-Niell, R. S., and Haight, G. R. (2016). Optimal Inspection of Imports to prevent Invasive Pest introduction.pp.1-40
Ching-Ho,Y., Heng, M., Chi-Huang, Y., and Chia-Hao, C. (2015).The Economic Design of Variable Acceptance Sampling Plan with Rectifying Inspection. Kybernetes, 44(3):440-450.
Fallahnezhad, M. S., Sajjadieh M., Abdollahi, P. (2014). An Iterative Decision Rule to Minimize Cost of Acceptance Sampling Plan in Machine Replacement Problem. International Journal of Engineering, 27(7): 1099-1106.
Fallahnezhad, M. S., Ahmadi, Y. (2016). A New Optimization Model for Designing Acceptance Sampling plan Based on Run Length of conforming units. Journal of Industrial and System Engineering, 9(2): 67-87.
Fallahnehad, M. S., and Qazvini, E. (2016). A new Economical Scheme of Acceptance Sampling Plan in a Two-stage Approach Based on the Maxima Nomination Sampling Technique. Publish online in Transactions of the Institute of Measurement and Control. Pp.1-7.
Fallahnezhad,M,Qazvini,E and Abessi, M. (2017).Designing and Economical Acceptance Sampling plan in the presence of inspection errors based on Maxima Nomination Sampling Method. Scientia Iranica, 25(3): 1701-1711.
Frishman, F. (1960). An extended Chain Sampling Inspection Plan. Journal of Industrial Quality Control, 17: 10-12.
Gao, F. (2003). Studies on Chain Sampling Schemes in Quality and Reliability Engineering. A Thesis Submitted for the Degree of Doctor of Philosophy Department of System and Industrial Engineering. National University of Singapore. Pp.101-210
Hagenimana, E, Lixin, S, Kandege, P. (2016). Technical Application for Inspection Sampling for Repairable Systems in an Economic System. SpringOpen Journal..pp.1-20.
Hoang, P.(2006). Springer Handbook of Engineering Statistics. Springer-verlag London Limited, Pp.264.
Hsu, L., and Hsu, J. (2012). Economic Design of Acceptance Sampling plans in a Two-Stage Supply Chain. Advances in decision Science, 2012: 1-14.
Mistra, R. C., and Sandilya, A. (2009). Reliability and Quality management. New Age International Publishers, Ansari Road, Daryaganj, New Delhi, Pp.132-133.
Montgomery, D. C. (2009). Introduction to Statistical Quality Control. 6th Edition, John Willey & Sons, Inc.Arizona USA, Pp. 632-650.
Muhammad, B., and Chang, W. (2016). Minimization of Inspection Cost by Determining the Optimal Number of Quality Inspectors in the Garment Industry. Indian Journal of fibre and textile research, 41: 346-350.
Muhammad, A. S., Randolph, K. Henriqueta, N., and Antonio, A. (2017). Cost of Quality: Evaluating Cost –Quality Trade-offs for Inspections Strategies of Manufacturing Processes. International Journal of Production Economics, 188: 156-166.
Namin, S., Pakzad, A., and Nezhad, M. (2017). A DEA –Bases Approach for Multi-Objective Design of Attribute Acceptance Sampling Plans. International Journal of Data Envelopment Analysis, 5(2): 12-24.
Nezhad, M. S., and Nasab, H. H. (2011). Designing a Single Stage Acceptance Sampling Plan Based on the Control Threshold Policy. International Journal of Industrial and Production Research, 22(3): 143-150.
Subramaniam, S., and Yuvaraj, V. (2011). Bayesian Single Sampling Plan fro Attributes based on a Two point Prior Distribution. International Journal of Civil Engineering Research, 2 (2): 283-290.
Valtteri, T. (2012). Cost Modelling of Inspection Strategies in Automotive Quality Control. Journal of Engineering Management Research,1(2): 33-38.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2022 ST Iorkegh , P Osanaiye
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Contact Us
Editorial Team
Join As A Reviewer 
Request For Print Copy
Cprint Publishers